Linux Flashing Guide

Revision as of 11:12, 22 June 2018 by Dguidi (talk | contribs) (Dguidi moved page LinuxFlashingGuide to Linux Flashing Guide without leaving a redirect)

Revision as of 11:12, 22 June 2018 by Dguidi (talk | contribs) (Dguidi moved page LinuxFlashingGuide to Linux Flashing Guide without leaving a redirect)

Contents

Introduction

This document will guide you through the necessary steps needed to flash your Gemini with a Linux or Android/Linux OS.

Please note: Flashing Android or Linux will delete any user data on the device. Please make sure you have a backup of any important data before starting!

Important Note: please don’t use other tools to flash firmware fo your Gemini as it’s easy to loose key information such as the IMEI number. In particular, never use the “Format all + download“ option in the SP Flash Tool as this erases key information stored in the NVRAM partition and can lead to a non-functional device.


There are 3 steps needed to install Android/Linux your Gemini:
  1. Install the FlashTool software on your Windows PC or Linux PC
  2. Customise your Gemini partition table. Using a simple tool, you will be able to specify the space you want to reserve for Linux and for Android. You will also be able to choose the firmware to download, at the moment we support Android, Rooted Android, Debian and Sailfish OS.
  3. Flash the firmware on your device


These steps are detailed in the next sections.

Download and Install FlashTool on Windows

The first step to install FlashTool on a Windows PC is to install the flash tool drivers. The drivers are needed for your Windows PC to communicate with your Gemini, the minimum requirement is to have a 64bit Windows operating system.
You can find the latest drivers here: [download/FlashToolDrivers.zip Windows Flash Tool Drivers]
Once downloaded, unzip the archive. You will find a folder called FlashToolDrivers, open the folder and double click on the Install (install.bat) file. Allow the installation to complete by clicking Yes when asked to make changes.
Now that the drivers have been installed, you can download the latest Windows flash tool: [download/FlashToolWindows.zip Windows Flash Tool]
Once downloaded the Windows FlashTool, please unzip it to reveal the FlashToolWindows folder. Next, run the flash tool by double clicking on flash_tool (flash_tool.exe) file in the FlashToolWindows folder.

Download and Install FlashTool on Linux

The following procedure has been tested on Debian 9.0, Ubuntu 18.04 (see notes below) and Fedora 28 (see notes below).

You can find the latest Linux flash tool software here: Linux Flash Tool

Once downloaded, extract the flash tool by typing:

tar -zxvf FlashToolLinux.tgz

Before running the flash tool you will need to add some rules to udev.

Create the blacklist file by typing (using either the "sudo command" or syntax or simply typing the command as root) :

sudo gedit /etc/udev/rules.d/20-mm-blacklist-mtk.rules

And inside the file put the following 2 lines:

ATTRS{idVendor}=="0e8d", ENV{ID_MM_DEVICE_IGNORE}="1"
ATTRS{idVendor}=="6000", ENV{ID_MM_DEVICE_IGNORE}="1"

After that, restart the udev:

sudo service udev restart

Finally, run the flash tool application by entering into the FlashToolLinux folder and typing:

cd FlashToolLinux

sudo ./flash_tool.sh


Notes - Ubuntu 18.04

On Ubuntu you will need to install the following dependency:

sudo apt-get install libjpeg62

Notes - Fedora 28

On Fedora you will have to write the following command to allow applications running with root privileges to access the X server (this will fix the lines above for both gedit and flash_tool):

xhost +local:

Additionally you will have to restart the udev service by typing (or rebooting your machine):

udevadm control --reload-rules && udevadm trigger

Finally, you will need to install the following dependency:

sudo yum install nas-libs-1.9.4-13.fc28.x86_64


Building the flash tool from source

You can also build the flash tool by yourself, the code is hosted on github: Flash Tool Source


Customise your Gemini partition table

If you choose to flash a Linux or Android-Linux firmware, then you will have to repartition your device, reserving some space for Linux and some for Android. To repartition your Gemini you will have to use our partition tool, available at http://support.planetcom.co.uk/partitionTool.html. A screenshot of the tool is provided below.

Screen Shot 2018-06-20 at 11.06.06.png


You can choose the partition size for Linux and Android by dragging the planet slider left or right. You can choose to have an Android-only Gemini, a multi boot Linux-Android or a Linux-only Gemini. Once you have selected the partition sizes you have to select your Gemini model using the appropriate drop down menu.

There are 3 Gemini versions, please make sure you select the right version for your device:

  • WiFi-Only Gemini users should select "Gemini WIFI-Only".
  • 4G Gemini users using x25 chip (early release Geminis) should select "Gemini x25"
  • Gemini 4G x27 users should select the "Gemini x27" option.

If you are not sure about your Gemini version, just check under Settings -> Wireless & networks. If you see a menu called SIM cards, then you have an x27 Gemini, otherwise you have an x25 Gemini.

After selecting the partition size, you can select the operating systems to use for each boot mode. Gemini supports 4 boot modes (see the Linux boot notes section below for more information):

  • Boot 1: This is the default booting option when no buttons are pressed.
  • Recovery Mode: Esc (On) is pressed. This will always boot into overy mode.
  • Boot 2: Side button is pressed.
  • Boot 3: Esc(On) key is pressed and Side button is also pressed

As an example, the following screenshot shows a Gemini WIFI-Only model, configured with 28 GB for both Android and Linux, where the boot modes are set as:

  • Boot 1: Standard Android
  • Boot 2: Debian GNU/Linux
  • Boot 3: Sailfish OS


Screen Shot 2018-06-20 at 11.16.03.png


After you made your selection, there are 3 modules to download using the buttons on the right:

  • The Base firmware contains the basic Android firmware. This is the main component, it needs to be extracted to reveal the Gemini Base firmware folder. All the other component need to be copied/unzipped here.
  • The Scatter file contains the definition of your Gemini partition, based on your selection. This needs to be copied into the firmware folder
  • The optional Linux module (Debian, Sailfish or Debian+Sailfish) contains the additional Linux firmware. This needs to be unzipped into the firmware folder

You should end up with the extracted Base firmware folder, containing also the scatter file and the unzipped optional Linux module.

NOTE: It is important to keep a backup of the custom scatter file that you created, you will need it each time you want to update your device (for example Android) without loosing your data.


Configuring Flash Tool

Use the choose button as in the following screenshot to load the scatter file that you will find inside the downloaded firmware. In particular:

  • Downlad-Agent should be set to the file MTK_AllInOne_DA.bin, which is located in the FlashToolWindows or FlashToolLinux folder.
  • Scatter-loading file should be set to the specific scatter file of the firmware that you customised, which is located in the firmware folder


Your screen should look like the following screenshot:


Screen Shot 2018-06-21 at 11.35.58.png


In particular, all the partitions should be checked. If you see any unchecked partitions in the list, make sure you unzipped the Linux module in the firmware folder and try again.


Backup the NVRAM partition

Before flashing the device with a different firmware it is a good idea to backup the current NVRAM partition. This partition stores key information for your Gemini, including the IMEI number. If it gets lost or damaged, your Gemini will not be able to take or receive calls.


The provided flash tool is already configured for your Gemini. To create a backup of your NVRAM partition, just click on the Readback tab and then on the Add button. A row will appear in the table as in the following screenshot.


Screen Shot 2018-06-21 at 10.52.02.png


Next, just click the Read Back button, connect your Gemini to your PC and restart the Gemini. Once booting, the flash tool will detect the unit and will write the NVRAM partition on a file on your hard disk called NVRAM0 (see screenshot below). It’s a good idea to keep this file as a backup, together with the customised Scatter file.

Flashing the Gemini Linux firmware

Be sure to follow the previous step to store a copy of the NVRAM partition as backup.Now click back on the Download tab.
Select the Firmware Upgrade option from the drop down menu. This will automatically select all the partitions in the table.

To start the flashing process, just click the big Download button, connect your Gemini to your PC and restart the Gemini. Once booting, the flash tool will detect the unit and will start flashing the device with the selected firmware.

The following screenshot shows a successfully completed flashing process:

Screen Shot 2018-06-21 at 12.08.02.png


Linux boot notes

The multi boot mechanism works as follow.

Starting from a switched OFF Gemini, press the Esc (On) key to start the unit until the Gemini vibrates. Once you feel the vibration you can choose the boot mode by pressing the following key combination:

  • Boot 1: This is the default booting option when no buttons are pressed.
  • Recovery Mode: Esc (On) is pressed. This will always boot into overy mode.
  • Boot 2: Side (silver) button is pressed.
  • Boot 3: Esc(On) key is pressed and Side button is also pressed

After the screen turns ON you can release the keys.


Make sure you also read the